Conveyor Belt Scales
Scales are gravimetric devices. In other words they are devices that measure the force that gravity exerts on mass. Scales can be classified as two types: differential and integral weighing devices.
Differential Weighing Devices
Differential weighing devices are the most common. You begin at one
weight on a scale and then add or subtract weight to give you the
difference between the beginning and ending reading. For example, a
truck scale starts at one reading, generally zero, and then goes
to a different weight reading when you drive a truck onto the scale
platform. The difference between the two readings is the weight of the truck.
Truck scales, rail scales, platform scales, package scales, postal scales,
counting scales, etc. all operate on this principle.
Batching scales weigh ingredients into a weigh hopper on a differential
basis, one ingredient at a time. Bulk weighers weigh and dump into and
out of a bulk material weigh hopper to record the high weight, the low weight,
and the difference which is the total weight transferred of bulk materials.
Loss-in-weight feeders use a feeding device to empty a weigh hopper
at a controlled rate using the rate of change of weight
(the differential weight change) as the measuring element.
Integrating Weighing Devices
Integrating weighing devices are the second category of scales.
Conveyor belts scales are integrating weighing devices that use
a simple integral calculus summation process to measure a conveyed
quantity of material. Two variables are involved: weight and speed.
A weight function measures the weight of a small section of a conveyor.
The gross weight on the scale is the weight of the belt, the belt conveyor
idler and the material on the belt. The net weight of material only is the
gross weight less the weight of the supported section of the belt and the scale idler.
The speed function is the second variable to be measured. Most modern speed
sensors are rotary digital pulse generators. These can be optical, magnetic or
other on/off sensing units. They are mounted on a pulley or wheel that rotates
as the belt moves. They generate an on/off signal as they move which is directly
proportional to the distance the belt moves and the speed of the belt.
Types of Belt Scale Weighing Technologies
Many different types of weighing technologies have been used over the
years for conveyor belt scales. The first belt scales used mechanical
integrators. The speed of the belt drives a disk. A ball or another disk
rolls on this disk at right angles to the speed disk. The position of the ball
or second disk is controlled by the weight on the scale. If the ball is in the
centre of the speed disk, it does not rotate at all. As the ball is moved to
the outside, it rotates faster and faster. The speed of the ball is a mechanical
multiple of the speed of disk and the position of the ball on the disk. The
ball is connected to a shaft that drives a totalizer. The speed of this shaft
is the rate.
Another method of determining the load on a conveyor belt was to use
a nuclear source on one side of the belt and a detector on the other side.
The more material that is on the belt, the less radiation is detected.
You get an inversely proportional signal of absorbing mass on the belt.
Using this along with belt speed you could make a belt scale.
These were never very wide spread in actual use.
LVDT’s (linear variable differential transformers) are position sensing
devices that have been used in conjunction with spring mechanisms
to measure belt weight. They are non-contacting sensors and
generally have spring mechanisms that are rugged in nature which gives
them very good overload characteristics. On the down side,
they can exhibit problems with thermal effects on the mechanical springs.
These effects can be both on zero because of thermal expansion
and on the span due to modulus of elasticity changes.
Strain gage load cells are commonly used in scales today.
Many have been adapted to mechanical lever scales using a
lever system to sum forces at a single point where a load cell is used
to read the resultant force electronically at this point. These scales were
Common for retrofit installations on truck scales for example. Also,
Strain gage load cells were initially very expensive and limited to in-line
Tension and compression forces. This made mechanical hybrid load cell
mechanisms popular. Some belt scales are made with this technology
today, but their use is declining.
Today, most scales are full strain gage suspension types. They use little
or no mechanical mechanisms and the load platform is directly supported
by the load cell system. Most new conveyor belt scales use this
technology. Overload stops are built into the load cell mounting systems
to make them rugged and reliable. Also, they are simple in their overall
design. Single point suspension load cell designs allow for off-centre loading.
This also compensates for any extraneous side loading that could effect
the true weight component of the belt load forces that we are measuring.
There are advantages and disadvantages when considering conveyor
belt scales. As an integrating device, a conveyor belt scale
is a very compact device that fits into conveyor systems.
The scale handles large quantities of raw materials on a continuous basis.
It does not require large batch hoppers, truck scales or
rail scales. It can handle rates that make the application of differential
scales almost impractical. Loading and unloading ships is one example.
Belt scales have their weak points. First, belt scales can run for extended
periods of time without returning to zero. This means that any build-up
On the scale that affects the zero will not be detected until the scale is run
Empty. A zero error is not a one-time error. This error is continuously
Added along with the weight of actual material. Also, extraneous forces
such as wind loading, changing belt tension, excessive vibration, and
mechanical interference with the scale can cause errors in the weighing
system. The scale does not know the difference between the forces
from actual material we are trying to weigh and the forces from external
noise. Although this is true of all scales, the ratio of signal to noise is
much better on differential weighing devices than on integrating devices.
Integrating belt scales are weighing a small portion of weight on a
continuous basis and external noise can be significant. Care must be
taken to correctly install a belt scale and to protect it from external influences.
